
Gate Installation and Repair in Lansing, MI
Lansing Capital Fence hangs and fixes gates in Lansing, MI, Mason, Okemos, DeWitt and Grand Ledge, and out in Charlotte, Portland and Webberville.
Request a quote
Tell us why you want a fence and which yard it goes in. Someone calls you with a range.
The hinge post is the post that the gate hangs on and is the most important post in the gate area. This hinge post should be deeper and heavier than all the other posts, since it has a lot of weight put on it. The post should always be below the frost line of 42 inches in this area.
- Hinge posts dug deeper and larger than line posts
- Posts checked plumb before the concrete sets
- Swing direction settled with you before hanging
- Sag traced to the post before new hinges go on
- Pool gates that close and latch by themselves
At a glance
| Typical gate | $150 to $500 installed |
|---|---|
| Gate repair | $50 to $400 |
| Manual driveway gate | $300 to $1,200 installed |
| Widths | Walk 3 to 6 ft; double drive 8 to 12 ft |
| Pool gate | Self-closing, self-latching, latch 4 ft up or higher |
| Driveway sight line | Nothing blocking a 10 by 10 ft triangle at the drive |
Gates We Hang and Fix Around Lansing

Side Yard Walk Gates
The gate between the driveway and the backyard gets opened more than any other. Measure the mower deck and the wheelbarrow, then leave a hand-width spare on each side.

Double Drive Gates
Two leaves of 4 to 6 feet each open the yard to a trailer or a boat, with a cane bolt dropped into the ground to hold the passive leaf. Lansing keeps a 10 by 10 foot triangle at the drive clear so drivers can see the sidewalk.

Sagging Gate Repair
One that swung clear for years and now drags is telling you its post moved, or its hinge screws worked loose. Catch it before the dragging corner splits the frame.

Latches and Hardware
Gravity latches, lockable latches, heavy strap hinges and spring closers. A latch that stops catching a few weeks after install usually means the post settled.
More Gate Work
Pool Gates
Lansing's pool rule asks for one that closes and latches on its own, with the latch at least 4 feet up and a gap underneath that stops a 4-inch ball. Each spring, open it halfway and let go: it should latch without help.
Rolling Gates for Business Lots
Openings of 12 to 20 feet on a lot or storage yard often suit a rolling gate, which slides along the fence instead of swinging into the drive. A rolling chain link gate usually runs $350 to $1,000 or more before installation.
Steel Frames Inside Wood Gates
A wood frame racks as the boards dry and swell. Steel under the pickets stays square, and we'd use it on any wood gate wider than a walk gate.
Why a Gate Sags and What Fixes It
When a gate sags, it typically means the gate is getting older and the structure is failing. An 80-pound gate can have over 200 pounds of pressure on the hinge post. If the hinge post seems to be good and solid and still plumb, then putting diagonal supports on and lifting the gate into place before these are screwed on can be a decent fix.
Fix the gate itself
When the post is plumb and the gate still drops, the frame has racked out of square. A rigid brace has to climb from the low hinge corner to the high latch corner, so it pushes. A tension wire runs the opposite way, so it pulls. Fitted backwards, either one does nothing, so we check the direction before anything else.
Reset or replace the post
A tipped post gets dug out and reset deeper in fresh concrete, or replaced with a heavier steel one, which holds a gate square longer than wood.
How a New Gate Goes In
Choose the swing
Inward, outward, left or right, settled with you on the ground first.
Size the opening
Measure what has to pass through it. Walk gates run 3 to 6 feet, and double drive gates 8 to 12.
Call MISS DIG 811
Michigan wants three business days’ warning before a shovel goes in.
Dig the hinge post deeper
Gate posts go larger and deeper than line posts, toward the 42-inch frost line.
Plumb it before the concrete sets
It gets checked on two faces while the mix is wet. A post that starts out leaning never recovers.
Wait for the cure
Concrete takes one to four days to cure. A gate hung on green concrete starts a lean within weeks.
Hang it and set the latch
An even gap where it latches and clearance over the ground, then we test the latch with you from both sides.
Gate Cost in Lansing
A typical gate can cost around $150 to $500, while a gate repair can run around $50 to $400. It depends on what is wrong with it. We would say it depends on your budget. If you can get away with a gate repair, then that can be a good way to go, unless the gate and the post it hinges to are failing. Sometimes repairing these is only a band-aid and lasts a short while, so if it’s past a certain point, in the long run we would recommend replacing the gate and setting a new hinge post deep in the ground below the frost line.
When you need a wider gate, we would recommend a wider single walk gate at a cost of around $150 to $500. A double gate, which is typically 8 to 12 feet wide, starts at $300 and goes all the way up to $1,200 installed. It depends on budget and whether you have the room for a larger gate.
| Gate | Cost |
|---|---|
| Typical gate | $150 to $500 |
| Gate repair | $50 to $400 |
| Wood or vinyl garden gate | $300 to $600 |
| Vinyl gate, 4 to 6 ft | $150 to $780 |
| Manual driveway gate | $300 to $1,200 |
| Chain link walk gate, parts | $80 to $200 |
| Chain link drive gate, parts | $175 to $500 |
Every row is a national figure for 2026. Hinge posts here go toward the frost line, which adds digging.
What affects the price
Every job is quoted after we see it. These are the things that move the number up or down.
Material
A manual chain link gate runs $180 to $1,000 nationally, a wood one $300 to $4,000
Width
A double drive gate needs two hinge posts and a latch post between them
Repair or rebuild
Rehanging on a reset post costs far less than a new gate and posts
Pool code
Spring hinges plus a latch mounted high mean extra parts
Frame
Steel inside a wooden or PVC gate adds cost and keeps it square
Get a quote on your gate installation and repair
Say what the fence has to do, which part of the yard it runs through and roughly how long it is. Expect a call with a ballpark figure, and the two or three things that would move it, like a corner lot, a second gate or old posts set in concrete.
Gate Installation and Repair in nearby areas
Gate Installation and Repair FAQs
How much does it cost to replace a fence gate?
A typical gate replacement runs $150 to $500. It depends on what's wrong with it. If it is a leaning hinge post, then a new post set in concrete would be needed.
Can a sagging gate be fixed without replacing it?
Most gates that sag start at the post. The post can be reset and plumbed. Also, you can put a diagonal board or a cable kit from the lower corner back up to the hinge post.
Which way should my gate swing?
A gate should always swing into the yard for most homes and never block the sidewalk. Also, the open gate should never block a driver's view, for safety.
How wide should a gate be for a riding mower?
When building a gate to fit a riding mower, you should measure the deck of the mower at its widest points. We would recommend making it approximately a foot wider than this measurement.
Will a wheel stop my gate from dragging?
A wheel can stop the gate from scraping on the ground. This is typically meant for long, heavy gates.
Can I put a gate across my driveway near the sidewalk in Lansing?
Yes, but a triangle at the corner of the driveway must stay open so drivers can see people on the sidewalk. A solid gate blocks the view of drivers and people walking.
Request a quote
Ring (517) 418-7986 if you would rather talk now, or leave the details below and expect a callback.
